The 7721DD4-HD Quad Serial Data De-embedder extracts 4 x RS-232 or RS-422 serial data streams and GPI contact closure information from a 270Mb/s SD-SDI or 1.5Gb/s HD-SDI video signal. A data error detection and correction scheme is also applied to maintain data integrity on the output of the data de-embedder. At the embedded packet layer, data packets resemble and have the same group DIDs as embedded audio packets. The data is un-packetized and extracted from the AES sub-frame according to SMPTE ST 337. Adding the +GPI option to the decoder (model 7721DD4-HD+GPI) allows the user to decode remote control contact closure information from VITC (SD) or SMPTE ST 12-2 ATC (HD) user bits instead of decoding the GPI information from the AES embedded data stream. This feature allows the user to use remote control user bit patterns to control the six GPO relay outputs. At the encoder end the 7721DE4-HD+GPI GPI Encoder module encodes the remote control user bits in VITC or SMPTE ST 12-2 ATC. The 7721DD4-HD module occupies one card slot and can be housed in the 1RU 7801FR frame which holds up to four single or two dual slot modules, the 3RU 7800FR frame which has a 15 slot capacity, the portable 3RU 350FR frame which has a 7 slot capacity, or a standalone enclosure which holds a single module.
Automatic detection of SD-SDI or HD-SDI video input
4 x RS-232/422 serial outputs with selectable baud rate
Parity selection: none, even or odd
Support serial input with BREAK character according to SMPTE ST 207
Packetize data into sub-frame AES format according to SMPTE ST 337
Share the same group DIDs as for embedded audio, selectable from group 1 to 4
Group selection for extracting data from one of four Audio Groups
Redundant data transmission to allow data error detection and correction at the receiver end
Six GPI outputs to embed simple control information into the video input
Automatically remove the existing embedded packets when the conflict of group DID occurs
Card edge LEDs indicate video signal and data presence, cable equalization and module fault
With GPI Option - Decodes GPO relay contact closure information from VITC or ATC user bits (instead of decoding the GPI information from AES data)
De-embedder/Embedder Type - AES
De-embedder/Embedder Type - Other
Spec Sheet available - Yes
Serial Video Input - Standard:
SMPTE ST 259-C, SMPTE ST 292-1
Serial Video - Number of Inputs:
1
Serial Video Input - Connector:
BNC per IEC 61169-8 Annex A
Serial Video Input - Equalization:
Automatic 300m @ 270Mb/s, 100m @ 1.5Gb/s with Belden 1694A (or equivalent)
Serial Video Input - Return Loss:
> 15dB up to 1.5Gb/s
Serial Video Output - Standard:
SMPTE ST 259-C, SMPTE ST 292-1 + embedded data
Serial Video - Number of Outputs:
2 (1 bypass relay protected)
Serial Video Output - Connector:
BNC per IEC 61169-8 Annex A
Serial Video Output - Signal Level:
800 mV nominal
Serial Video Output - DC offset:
0V ±0.5V
Serial Video Output - Rise/Fall Time:
600ps nominal SD-SDI, 200ps nominal HD-SDI
Serial Video Output - Overshoot:
< 10% of amplitude
Serial Video Output - Return Loss:
> 15dB up to 1.5Gb/s (bypass relay protected); > 10dB up to 1.5Gb/s
Serial Video Output - Wideband Jitter:
< 0.2UI
Serial Data Output - Standard:
RS-232 or RS-422 (jumper selectable)
Serial Data - Number of Outputs:
4
Serial Data Output - Connector:
Terminal block
Serial Data Output - Baud Rate:
110, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, or 115200
Serial Data Output - Format:
8 data bits, parity (one, even or odd), 1 or 2 stop bits
General Purpose Inputs - Type:
Normally open relay contact
General Purpose - Number of Outputs:
6
General Purpose Inputs - Connector:
Terminal block
General Purpose Inputs - Signal Level:
Internal pullup to +5V or +12V nominal (jumper selectable); For other voltages up to 5V DC remove jumper
Number of Slots:
1
Active Power:
12 Watt
Current Draw:
2 Amps
DC Voltage:
12 Volts
Regulatory Compliance:
FCC Part 15 Class A, EU EMC Directive