Signal Processing Systems : Distribution Amplifiers : Evertz - 500DA2Q-3G

3G/HD/SD SDI Dual Reclocking Distribution Amplifier (32 - 1 x 4)

Model: 500DA2Q-3G

Normal reclocked mode for SMPTE ST 424 (3Gb/s), SMPTE ST 292-1 (1.5Gb/s) and SMPTE ST 259 (270Mb/s)
Jumper selectable non-reclocked mode for all other SMPTE ST 344, SMPTE ST 259, SMPTE ST 310 and DVB-ASI data rates
Fully hot-swappable from front of frame with no BNC disconnect required
Independent isolated output drivers to ensure no cross channel loading effects (i.e. no need to terminate unused outputs)
Outputs maintain polarity from input to output for DVB-ASI applications

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The 500DA2Q-3G Dual 3G/HD/SD-SDI Reclocking Distribution Amplifier provides the highest density DA in the industry allowing up to 32 3Gb/s, HD-SDI or SD-SDI Distribution amplifiers in a 3RU rack space. This module provides inexpensive distribution of your SMPTE ST 424 (3Gb/s), SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259 (270Mb/s), DVB-ASI or SMPTE ST 310 (19.4Mb/s) or any other SDI signal within the 143Mb/s to 1.5Gb/s range. The 500DA2Q-3G features two auto-equalized inputs and can be individually set via jumpers for either reclocking or non-reclocking. The 500DA2Q-3G is housed in the 500FR frame that will hold up to 16 modules.

Normal reclocked mode for SMPTE ST 424 (3Gb/s), SMPTE ST 292-1 (1.5Gb/s) and SMPTE ST 259 (270Mb/s)
Jumper selectable non-reclocked mode for all other SMPTE ST 344, SMPTE ST 259, SMPTE ST 310 and DVB-ASI data rates
Fully hot-swappable from front of frame with no BNC disconnect required
Independent isolated output drivers to ensure no cross channel loading effects (i.e. no need to terminate unused outputs)
Outputs maintain polarity from input to output for DVB-ASI applications
Tally output on Frame Status bus upon loss of input signal for quality monitoring
VistaLINK® capable for remote monitoring via SNMP (using VistaLINK® PRO) when installed in 500FR frame with 500FC VistaLINK® Frame Controller
2 inputs; 4 reclocked outputs per input
SMPTE ST 424 (3Gb/s), SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259 (270Mb/s) when set to reclocking mode
SMPTE ST 344 (540Mb/s), SMPTE ST 259 (360Mb/s, 143Mb/s), SMPTE ST 310 (19.4Mb/s), DVB-ASI when not reclocking
Card Edge LEDs: Reclocker rate (3 LEDs), Reclocker locked, Reclocker bypass, Module Health Status

DA Video Input - 3GBs SDI
DA Video Input - HD-SDI
DA Video Input - SDI
DA Video Output - 3GBs SDI
DA Video Output - HD-SDI
DA Video Output - SDI
Spec Sheet available - Yes

Number of Inputs: 1
Number of Outputs: 4
Rack Units (Height): 3
Active Power: 6 Watt
DC Voltage: 12 Volts
Regulatory Compliance: FCC Part 15 Class A, EU EMC Directive
Standards (Reclocked Mode): SMPTE ST 424 (3Gb/s), SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259 (270Mb/s)
Standards (Non Reclocked Mode): SMPTE ST 344 (540Mb/s), SMPTE ST 259 (360Mb/s, 143Mb/s), SMPTE ST 310 (19.4Mb/s), DVB-ASI
Input Connector: BNC per IEC 61169-8 Annex A
Equalization (Input A): Automatic to 65m @ 3Gb/s, 100m @ 1.5Gb/s and 350m @ 270Mb/s with Belden 1694A or equivalent cable
Equalization (Input B): Automatic to 80m @ 3Gb/s, 150m @ 1.5Gb/s and 350m @ 270Mb/s with Belden 1694A or equivalent cable
Return Loss: > 15dB up to 1.5GHz; > 10dB up to 3GHz
Number of Outputs (2x4 Mode): 4 reclocked from each input. Reclockers can by bypassed separately for each input
Output Connector: BNC per IEC 61169-8 Annex A
Signal Level: 800 mV nominal
DC Offset: 0V ±0.5
Rise & Fall Time: 200 ps nominal
Overshoot: < 10 % of amplitude
Jitter: < 0.2 UI HD; < 0.3 UI 3G
Number of Slots: 1

3G/HD/SD-SDI Dual Reclocking Distribution Amplifier 60 kb - Data Sheet

Project List